EZ-GUI Ground Station

soon as I plug it in and connected it wiped my whole board OSD is not working the servos are jittery it was working just fine all I wanted to do was change the rates on my matek f411 wing using inav. all I do is connect and it ruined everything why is this even allowed in the Play Store please remove this app the board is ruined. it's not brick I'm able to reflash the firmware but nothing works anymore this is outrageous do yourself a favor and don't use this Cr-APP!

I'm running INAV with the Furious F35 controller. The app is very buggy and is not ready for prime time yet.

i lost all of my data program all wiped out from my flight controller using this app. can't reload it. w.t.f. i wasted my funds on this. what did I do wrong ????

When I am doing aux settings then it is showing warning no data received how to fix

No longer supported. Don't pay for the unlock.

while connect with arduino uno..its shows only no data received..why this problem

EZ-Gui Ground Station doesn't detect sensors, why?

DO NOT INSTALL! This app is no longer supported and should be removed from the store.

best app for open source flight controllers.....

it wont save my config settings

great app, thank you

will miss this app

work as it should

I have paid for the full app n now i cant save the setting it keep promt connected/disconnecting right aftr i try to save the setting..

Nice and easy to use lots of usefull extras, set up my prevously flashed f3 lite board. Ports and Sbus also sucsesfully enabled. Only one thing, I cant calibrate my oneshot escs otherwise good stuf. Thanks.

Great app😊 Tried with my rodeo150 when could not get into cleanflight.. So for me is better than clean and beta flight😊

Have spf3 inav 1.9.0 ez-gui ver 4.5.450 on tablet after clicking save it comes up hardware failure and crashes board then have to re-install board software. Ver4.1.421 on phone. Works fine

This app is nothing but a constant downgrade of itself. Not sure what's happening but every time I use it it somehow gets way worse.

Would give more stars but betaflight 3.2 and newer isn't supported and I should have to pay just to save aux switches

I try save the configurator today, its messed up with my fc. Omnibus f3 aio with inav 1.8

nice gui and dashboard. not able to use model control with cleanflight or inav. otherwise it would be a 5 *

Even without the other features, being able to tune your copter without needing to plug it in is what makes this app great (FYI make sure your MWC version is 2.3 or higher otherwise your copter may become unstable)

This app is great, easy to use, cheap to unlock and indispensible for UAV nerds. Just make sure you select lowest baudrate for bluetooth connection via MSP in iNAV.

For quads that you cannot tune pids through osd this is brilliant. 5 stars for that...

I tested it on my Omnibus f3 aio which has betaflight and it works like a charm, add 3d model of quad and rate/super rate curves and I'll give you 5 stars

Very useful indeed. But it would be useful to have a more comprehensive manual, preferably as a single pdf document that one could print.

I'll write something intelligent after hopefully flashing, first run and configuration on my Eachine Falcon 210 fpv racer Naze Omnibus F4 FC i am having issues sometimes my phone using otg usb sees the fc but sometimes not....

The free app work fine for me I used it for 2 months I just paid for the unlock so let's see

I like the configurator, it did do its job. But now I can't connect or flash my FC due to the update. Have tried many times in bootloader, but still. really didn't want to buy new FC's due to an update. Any help would be appreciated, will rate better if can work like before.

Doesn't work with SPRacingF3 running iNav. Gives voltage readout but nothing else.